Nanjing Hyderman Rubber & Plastic Co.,Ltd
Contact US
Address: No.9,Longjing Rd, Gaochun Economic Development Zone, Nanjing City, Jiangsu Province, China 211300
Tel: 86-25-56836319
Fax : 86-25-56836219
Home > News > Content
Rubber Products Good Performance And Low Cost
- Jul 11, 2017 -

First, the basic process of rubber products

With the rapid development of modern industry, especially the chemical industry, a wide range of rubber products, but its production process, but basically the same. To the general solid rubber (raw rubber) as raw materials products, its production process mainly include:

Preparation of raw materials → plastic refining → mixing → forming → curing → rest → test

Second, the preparation of raw materials for rubber products

The main materials of rubber products are raw rubber, with the agent, fiber materials and metal materials. (Cotton, hemp, wool and all kinds of man-made fibers, synthetic fibers) and metal materials (steel wire, copper wire), and the like is used as the base material; the mixing agent is the auxiliary material added to improve the performance of the rubber products; Is used as a skeleton material for rubber products to enhance mechanical strength and restrict product variants.

During the preparation of the raw material, the ingredients must be accurately weighed according to the formula. In order for the raw gum and the compounding agent to be mixed with each other, some materials need to be processed:

Raw rubber to cut rubber, broken into small pieces;

Such as paraffin, stearic acid, rosin, etc. to be crushed;

Powder containing agent containing mechanical impurities or coarse particles need to be removed;

Liquid compounding agent (pine tar, ancient malon) need to heat, melt, evaporate moisture, filter impurities;

Matching agent to be dry, or easy to agglomerate, mixing the old can not be dispersed evenly, vulcanization when the bubble, thus affecting product quality;

Third, the rubber products of plastic refining

Raw rubber is flexible, lacks the necessary performance (plasticity) during processing, and therefore is not easy to process. In order to improve its plasticity, it is necessary to plasticize the raw rubber; so that when the mixing agent is easy to evenly dispersed in the raw rubber; at the same time, in the rolling, molding process also helps to improve the permeability of the compound (infiltration Fiber fabric) and molding fluidity. The long process of biodegradation of raw rubber, the process of forming plastic called plastic. There are two kinds of plastic molding and plasticization. Mechanical plasticization is at a very high temperature, through the plastic mill mechanical squeeze and the role of friction, so that long-chain rubber molecules degrade from the high elastic state into a plastic state. Thermoplastic refining is the raw rubber into the hot compressed air, under the action of heat and oxygen, so that the degradation of long-chain molecules become short, in order to obtain plasticity.

Fourth, the mixing of rubber products

In order to adapt to a variety of different conditions of use, to obtain a variety of different performance, but also to improve the performance of rubber products and reduce costs, must be added in the raw rubber with a different agent. Mixing is the plastic blend of raw rubber and mixed with the mixture, placed in the mixing machine, through the mechanical mixing, so that with the agent completely and evenly dispersed in the raw rubber in a process. Mixing is the rubber products in the production process of an important process, if the mixing is not uniform, can not give full play to the role of rubber and complex agent, affecting the use of the product performance. The compound obtained after mixing is known as a rubber compound, which is a semi-finished material for the manufacture of various rubber products, commonly known as a compound, usually sold as a commodity. The purchaser can use the compound to be directly processed and vulcanized Need for rubber products. Depending on the formulation, the blend has a range of different grades and varieties that offer different options.

Fifth, the molding of rubber products

Molding method in the rubber industry is also a very important molding method, the rubber cut or punch into a simple shape, adding heating mold, in the molding at the same time curing, the product is hot off the mold. Many rubber mold products such as gaskets, shock absorbers (such as aprons, plastic sheet) and so on are produced by this method.

(1) main equipment

There are presses and molds. The role of the press is to apply pressure to the plastic through the mold. In the rubber processing, the press is called flat vulcanizing machine. The main parameters of the press include nominal tonnage, platen size, working stroke and plunger diameter, which determine the area, height or thickness of the press molded product, and the maximum molding pressure that can be achieved. Mold according to its structure characteristics, can be divided into overflow, not overflow and semi-overflow three kinds, of which half-overflow with the most used.

(2) the process

Divided into feeding, closing mold, exhaust, curing, stripping and mold cleaning, etc., if the products need to be embedded in the molding of the inserts, the insert should be placed before the insert. The main control conditions are pressure, mold temperature and molding time.